Tender Details
The works include but are not limited to the following:
Passive Fire Protection System:
1) Provide a passive fire protection system to all service risers at the slab penetrations. Fire seal the penetrations to separate each room from the room above and below it. Where a room has a balcony above it, seal the penetration in the room at low level and seal the penetration on the balcony at high level. The sections of riser in the room and the balcony will then form a single compartment.
2) Provide expanding fire seal type passive fire protection system (FRL -/90/90 minimum) to the full depth and width of the slab penetration. Provide formwork to the lower edge of the penetration as required.
3) Provide 2 x 32mm dia PVC pipes to the service risers at the slab penetrations to allow for future services in each fire rated location. The piping is to be able to be located from either side of the slab. Provide passive fire protection system inside the piping (FRL -/90/90 minimum).
4) Provide service preparation prior to installation of passive fire protection system. Clean and prepare existing services to enable passive fire protection system to be installed. Organise services in the service riser to allow ease of application of passive fire protection system.
Fire Doors & Walls and Building Work:
Service Riser Access Locations:
5) Demolish existing wooden panels and frames from service risers and remove from site. Relocate existing services in the rooms, including clotheslines, junction box conduit and other to allow installation and operation of the new doors.
6) Provide wooden doors with metal facing and metal edging, frames, hinges, night rim lockset to service riser access locations. Paint the doors to match the existing colour scheme.
Electrical Cupboards
7) Provide new fire rated door and steel frame (FRL -/120/30) to the electrical cupboards, with hinges and night rim lockset. Paint the fire doors to match the existing colour scheme.Block G East & West:Note: Fire sealing of penetrations is not required in Block G East & West service risers. Provide fire rated doors, etc. as detailed.
Electrical Switchboards:
8) Provide new fire rated walls (FRL 120/120/120), doors and frames (FRL -/120/30) to enclose the electrical switchboards. Provide a passive fire protection system (FRL -/120/120) to all service penetrations through the new fire walls. Paint the walls and doors to match existing colour scheme.
Pump Room
9) Relocate pump control panel into cavity adjacent to panels current location. Strip back sound proofing as required. Provide new fire door and frame (FRL -/120/30) at level to clear pump and services when opened. Provide fire panel to service riser access location. Provide fire panel at low level to service riser access location.
Drying, Washing and Other Rooms:
10) Provide new fire rated doors and frames (FRL -/60/30) to service riser access locations in drying, washing and other rooms.
Common Areas:
11) Demolish and remove timber panelling at 5 common area service riser access locations. Provide solid core timber door with veneer surface and frame to complement existing timber panelling. Provide timber panelling to enclose cavity between brick wall and existing timber panelling. Relocate services on or near timber panelling, including door hold open devices and hydraulics as required.
12) Provide fire rated access door and steel frame (FRL -/60/60) with automatic self-closing devices, hinges and night rim lockset to 6 common area service riser access locations. Paint the fire door red.
Additional Works:
13) Provide aluminium expanded mesh and frames to the all rooms with windows to keep out pigeons. Provide mesh 3mm thick, 50mm longway measurement, 20mm shortway measurement and 80% free air space. Paint the mesh to match the existing colour scheme. Secure mesh to the outside of the window frame to allow the window to be operated. Secure mesh so that it is permanently attached.
14) Demolish and remove timber panelling covering the tradeboxes and expose cavities in common area balcony level walkways. Provide permanent fire rated panels and frames (FRL -/60/60) to the cavity.
Completion
15) Provide 12 months maintenance (during Defects Liability Period)
16) Provide certification to BCA and Austalian Standards
17) Provide manual
18) Provide as-installed drawings
Invited Tenderers:
The following invited tenderers (pre-qualified from a previous EOI process) only may lodge tenders:
Alliance Alarms Fire Systems 660 603 373 377 20, 72-78 Percival Road, Smithfield, NSW, 2164
Automatic Fire Protection Design 190 020 510 41 113 /30 Campbell Street, Blacktown, NSW, 2148
CBC Facilities Maintenance 560 586 169 89 104 Auburn Street, Wollongong, NSW, 2500
Fireteq 410 924 517 35 Unit 46, 9 Hoyle Avenue, Castle Hill, NSW, 2154
Heyday Group 840 964 391 91 9 Waterloo Road, North Ryde, NSW, 2113
Tyco Fire & Security P/L T/A Wormald 980 086 595 96 38 South Street, Rydalmere, NSW, 2116
Passive Fire Protection System:
1) Provide a passive fire protection system to all service risers at the slab penetrations. Fire seal the penetrations to separate each room from the room above and below it. Where a room has a balcony above it, seal the penetration in the room at low level and seal the penetration on the balcony at high level. The sections of riser in the room and the balcony will then form a single compartment.
2) Provide expanding fire seal type passive fire protection system (FRL -/90/90 minimum) to the full depth and width of the slab penetration. Provide formwork to the lower edge of the penetration as required.
3) Provide 2 x 32mm dia PVC pipes to the service risers at the slab penetrations to allow for future services in each fire rated location. The piping is to be able to be located from either side of the slab. Provide passive fire protection system inside the piping (FRL -/90/90 minimum).
4) Provide service preparation prior to installation of passive fire protection system. Clean and prepare existing services to enable passive fire protection system to be installed. Organise services in the service riser to allow ease of application of passive fire protection system.
Fire Doors & Walls and Building Work:
Service Riser Access Locations:
5) Demolish existing wooden panels and frames from service risers and remove from site. Relocate existing services in the rooms, including clotheslines, junction box conduit and other to allow installation and operation of the new doors.
6) Provide wooden doors with metal facing and metal edging, frames, hinges, night rim lockset to service riser access locations. Paint the doors to match the existing colour scheme.
Electrical Cupboards
7) Provide new fire rated door and steel frame (FRL -/120/30) to the electrical cupboards, with hinges and night rim lockset. Paint the fire doors to match the existing colour scheme.Block G East & West:Note: Fire sealing of penetrations is not required in Block G East & West service risers. Provide fire rated doors, etc. as detailed.
Electrical Switchboards:
8) Provide new fire rated walls (FRL 120/120/120), doors and frames (FRL -/120/30) to enclose the electrical switchboards. Provide a passive fire protection system (FRL -/120/120) to all service penetrations through the new fire walls. Paint the walls and doors to match existing colour scheme.
Pump Room
9) Relocate pump control panel into cavity adjacent to panels current location. Strip back sound proofing as required. Provide new fire door and frame (FRL -/120/30) at level to clear pump and services when opened. Provide fire panel to service riser access location. Provide fire panel at low level to service riser access location.
Drying, Washing and Other Rooms:
10) Provide new fire rated doors and frames (FRL -/60/30) to service riser access locations in drying, washing and other rooms.
Common Areas:
11) Demolish and remove timber panelling at 5 common area service riser access locations. Provide solid core timber door with veneer surface and frame to complement existing timber panelling. Provide timber panelling to enclose cavity between brick wall and existing timber panelling. Relocate services on or near timber panelling, including door hold open devices and hydraulics as required.
12) Provide fire rated access door and steel frame (FRL -/60/60) with automatic self-closing devices, hinges and night rim lockset to 6 common area service riser access locations. Paint the fire door red.
Additional Works:
13) Provide aluminium expanded mesh and frames to the all rooms with windows to keep out pigeons. Provide mesh 3mm thick, 50mm longway measurement, 20mm shortway measurement and 80% free air space. Paint the mesh to match the existing colour scheme. Secure mesh to the outside of the window frame to allow the window to be operated. Secure mesh so that it is permanently attached.
14) Demolish and remove timber panelling covering the tradeboxes and expose cavities in common area balcony level walkways. Provide permanent fire rated panels and frames (FRL -/60/60) to the cavity.
Completion
15) Provide 12 months maintenance (during Defects Liability Period)
16) Provide certification to BCA and Austalian Standards
17) Provide manual
18) Provide as-installed drawings
Invited Tenderers:
The following invited tenderers (pre-qualified from a previous EOI process) only may lodge tenders:
Location
NSW Regions: Sydney
RFT Type
Pre-Qualified / Invited - Only those directly invited to tender, may obtain an RFT for the purpose of lodging a tender response.
Generally an invitation from a pre-qualified register of approved tenderers who have the ability to undertake the particular work or type of work proposed, a limited number of service providers are known to carry out the work or service (or in emergency or other restricted situations). Tenderers have usually been pre-qualified, accredited, or selected for the type of work and financial range. Competitive bids called from a standing offer (panel / period) contracts would also use this type.
Tender Respondents
| Business Name | Trading Name | Address |
|---|---|---|
| CBC Facilities Maintenance Pty Ltd | Paul's Building Consultants | 25 Military Road Port Kembla NSW 2505 AUSTRALIA |
| Fireteq Pty Limited | - | Unit 46, 9 Hoyle Avenue Castle Hill NSW 2154 AUSTRALIA |
Related Records
- Contract Award Notices:
- 0700942 Fireteq Pty Limited
Additional Details / Instructions
Non Mandatory Site Meeting: Monday 18/06/07 2:30 pm
Documents available for this RFT(issued on 13/06/2007):
Both softcopy (electronic download files) and hardcopy (paper) complete copies of this RFT are available. Hard copy have been supplied direct to the invited tenderers. Soft copy may be downloaded as below.
An Exhibited hard copy maybe available for public viewing by arrangement.
Obtaining the Documents:
First time visitors to this web site who wish to download or order documents will need to self-register on this web site to gain access to any documents.
A full soft copy of this RFT can be downloaded from this web site free of charge. To obtain the provided RFT document(s) you must download to your own computer all the files provided (including addenda), by clicking on the blue "DOWNLOAD A SOFT COPY" link at the bottom of this page and following the on-screen instructions.
Lodgement of tender:
Your completed tenders should be lodged as allowed in the RFT documents, however they may usually be lodged electronically via this web page.
As the tenderer you must be a registered user in this system. Click on the blue "LODGE A RESPONSE" link at the bottom of this page and follow the on-screen instructions.
Optimum size of lodgement files is less than 7MB, and if your tender is larger in total it should be broken down into smaller files, and uploaded in separate identified lodgements. The required response documents should not be bundled with supporting documentation. Note also that during the period 11pm to 3am system maintenance is carried out and successful lodgment may not be achieved.
PC Software Requirements:
To be able to open and read/view the downloaded files for this RFT you may require certain software to be installed on your PC:
An Internet connection to lodge completed responses.
This web site has been optimised for the Microsoft Internet Explorer and Netscape Navigator web browsers.
The minimum requirements are as follows IE version 5.5 or later, Firefox 1.0, Netscape Navigator Ver 4.7 or later with Cipher Strength = 128bit. Suggested minimum monitor resolution is 800x600.
Your web browser MUST be set to accept cookies. You will not be able to Register or accesss the documents if cookies have not allowed.
The tenderer is responsible for the provision and installation of the necessary software
Having Problems?
Having problems with logging in, responding, downloading, opening or viewing files? Please refer first to the FAQ section under the On-line ?HELP button at the top of this page. Should this not resolve the issue tenders email 'mto@commerce.nsw.gov.au' may then be contacted (quote RFT number and issue)
Documents available for this RFT(issued on 13/06/2007):
Both softcopy (electronic download files) and hardcopy (paper) complete copies of this RFT are available. Hard copy have been supplied direct to the invited tenderers. Soft copy may be downloaded as below.
An Exhibited hard copy maybe available for public viewing by arrangement.
Obtaining the Documents:
First time visitors to this web site who wish to download or order documents will need to self-register on this web site to gain access to any documents.
Lodgement of tender:
Your completed tenders should be lodged as allowed in the RFT documents, however they may usually be lodged electronically via this web page.
As the tenderer you must be a registered user in this system. Click on the blue "LODGE A RESPONSE" link at the bottom of this page and follow the on-screen instructions.
Optimum size of lodgement files is less than 7MB, and if your tender is larger in total it should be broken down into smaller files, and uploaded in separate identified lodgements. The required response documents should not be bundled with supporting documentation. Note also that during the period 11pm to 3am system maintenance is carried out and successful lodgment may not be achieved.
PC Software Requirements:
To be able to open and read/view the downloaded files for this RFT you may require certain software to be installed on your PC:
- Adobe ® Acrobat Reader ® 5.0 (or more recent) - Please click here Adobe ® Acrobat Reader ® to be taken to a free download site now.
- WinZip ® 7.0 (or more recent) or equivalent - Please click here Winzip ® to be taken to a free evaluation download site now.
- Microsoft ® Word 97 (or more recent) or equivalent
- Microsoft ® Excel 97 (or more recent) or equivalent
- Any other required software specific to the RFT &..
The minimum requirements are as follows IE version 5.5 or later, Firefox 1.0, Netscape Navigator Ver 4.7 or later with Cipher Strength = 128bit. Suggested minimum monitor resolution is 800x600.
Your web browser MUST be set to accept cookies. You will not be able to Register or accesss the documents if cookies have not allowed.
The tenderer is responsible for the provision and installation of the necessary software
Having Problems?
Having problems with logging in, responding, downloading, opening or viewing files? Please refer first to the FAQ section under the On-line ?HELP button at the top of this page. Should this not resolve the issue tenders email 'mto@commerce.nsw.gov.au' may then be contacted (quote RFT number and issue)
